You may scoff,  but try my changes,  they do work.  Only trying to help others.  

Dosser  

PS.  Now you've suggested upping comm_maxfps,  you do realise someone will try it.    

For general connection tweaks, which would affect SoF2, check out this website Speedguide.

Thanx for the great tips it has helped me good job!

Look tweaking the OS connection is good for surfing the net, but has squat to do with how SOF2 runs on the net, it by passes the OS.
Why put the rate at 25000 when "most" servers are capped at 8K?
Why put snaps at 40 when the server only gives you 20?
Maxpackets must be either same as FPS average or 1/2 or 1/3 of that average.
Adjusting packetdup is a tricky thing, most good connections this should be 0, with some lag 1 and with lots of lost packets 2.
But remember is you have packetdup at 2 you are effectivily getting 3 lots of the 1 packet and therefor only getting 1/3 of real data in your bandwidth.
So if the server is sending you 8K and you have packetdup 2 then your getting little real data if your not dropping any packets (use showdrop 1 in console and look for them), plus if you factor in snaps at 2 times the required amount.......
Cabler/xDSL should use: rate=sv_maxRate (check your server browser for that in the server info section).
maxpackets=1/1 1/2 or 1/3 of Average FPS.
packetdup=0 or 1 max unless you play servers outside your country.
snaps=20 (snaps is sv_fps which is generally always 20)

DoGTaGWorks  

Guys I have a very fresh install of SOF2 on WinME and it has been patched and I don't have a sof2mp.cfg file.  Do I need to create this file?

Derrrr, nm, I've been up for nearly 24 hours, now I see it...

LoL

can anyone plse send me his (well) tweaked sof2mp.cfg file cuz i did adjustments to it and now i think it's totally ####ed up
my email is tribe101@hotmail.com
tnx in advance !

Hello there!!!

Anyone out there know how to activate the radio through the keypad.

Any help will be great.

Thanks......

OK first you would set you're rate to 25k only if you do have a broadband connection. This would allow you to get whatever max rate the server is set at  whether it is 8k or 15k. If you're on a dial-up usually somewhere around 3k (give or take a little depending how good it actually is) should do the trick. Now there is no cg in the rate or snaps setting. Just bring down the console and type ex: /rate 25000 and then enter (or whatever is best for you're connection.) If you want to see what the rate is currently set at just type /rate and hit the enter key and it will show the current setting. This works for most other settings as well. Snaps.... default is 20 and I do not believe this is restricted by the server. However you do not want to go over 40 because of Punk Buster and the fact that this would be considered a cheat. That may also be dependent on what the server settings allow. ex: /snaps 40
cl_maxpackets would also be dependent on you're connection. Default should be good for most and is also monitored by PB. If you play with these settings and get kicked from a server or see warnings that you will be kicked by PB. Bring down the console and check the variable that it refers to. It will tell you what range it needs to be within. Change it and you will be fine. If you don't you will get teh boot. If you set snaps to high you would most likely see something like this if you set snaps to /snaps 100 :
[02.02.2003 14:21:30] VIOLATION (CVAR) #9001: St0opid Cheeta (slot #12) Cvar snaps = 100[347426b000e92552f15730cbd269d0f164.108.76.41:20100]

Some of this might help but be careful.  GL